天基核爆光辐射探测方法研究

通过计算提出了天基核爆炸光辐射探测指标要求,根据对源项信号特征的分析,设计了具有通带为1～4000Hz带通滤波器的天基核爆光辐射探测电路,采取了降噪措施,并以实验检验了其灵敏度、信噪比、频率响应和动态范围等性能,提出了软件修正系统误差的方法．     

微型桥梁索力测量毫米波雷达

在详细分析拉索雷达散射特性、频率法索力反演原理和拉索频率雷达测量原理的基础上,设计研制了一种77 GHz毫米波微型索力测量雷达,并给出了针对作用距离、精度和测量动态性能的系统约束参数集.与24 GHz K波段形变测量雷达进行比较,结果表明,所研制的毫米波微型索力测量雷达具有体积、质量和功耗小的技术特点,工程应用价值较大...     

南水北调中线工程安阳段渠坡换填土的强度特性研究

为了分析南水北调中线工程安阳段渠坡的稳定性,对该渠坡换填土在不同含水率下进行了不固结不排水三轴剪切试验.研究结果表明:剪切速率对基质吸力的影响较大,而对强度的影响较小;通过比较确定了合适的剪切速率;含水率相同的试样在不同围压下的强度值在pf -qf坐标上呈良好的线性关系;得到了试样在不同含水率下的总强度指标,建立了总内...     

弹性基上圆柱管弯曲行为的高阶剪切梁理论解

以弹性基上圆柱管为研究对象,基于高阶剪切变形梁理论推导了Winkler弹性基圆柱管弯曲变形的高阶剪切梁理论控制方程,给出四种典型工况弯曲问题的精确解.研究表明,无须假设剪切修正系数,只需引入适当横截面翘曲形状函数,高阶梁理论在圆柱管内外表面满足剪应力τxr为零的边界条件,且对于不同长径比和厚径比的圆柱管弯曲问题均能提供...     

A higher order coupled frequency characteristics study of smartmagneto-electro-elastic composite plates with cut-outs using finite element methods

This article deals with investigating the effect of cut-outs on the natural frequencies of magneto-electro-elastic (MEE) plates incorporating finite element methods based on higher order shear deformation theory (HSDT). In order to consider the influence of cut-out, the energy of the cut-out domain is sub-tracted from the total energy of the entire plate. The governing equations of motions are derived through incorporating Hamilton's principle and the solution is obtained using condensation technique. The proposed numerical formulation is verified with the results of previously published literature as well as the numerical software. In addition, this research focuses on evaluating the effect of geometrical skewness and boundary conditions on the frequency response. The influence of cut-outs on the degree of coupling between magnetic, electric and elasticfields is also investigated.     

Numerical simulation study on penetration performance of depleted Uranium (DU) alloy fragments

Due to its high strength, high density, high hardness and good penetration capabilities, Depleted ura-nium alloys have already shined in armor-piercing projectiles. There should also be a lot of room for improvement in the application of fragment killing elements. Therefore, regarding the performance of the depleted uranium alloy to penetrate the target plate, further investigation is needed to analyze its advantages and disadvantages compared to tungsten alloy. To study the difference in penetration per-formance between depleted uranium alloy and tungsten alloy fragments,firstly, a theoretical analysis of the adiabatic shear sensitivity of DU and tungsten alloys was given from the perspective of material constitutive model. Then, taking the cylindrical fragment penetration target as the research object, the penetration process and velocity characteristics of the steel target plates penetrated by DU alloy frag-ment and tungsten alloy fragment were compared and analyzed, by using finite element software ANSYS/LS-DYNA and Lagrange algorithm. Lastly, the influence of different postures when impacting target and different fragment shapes on the penetration results is carried out in the research. The results show that in the penetration process of the DU and tungsten alloy fragments, the self-sharpening properties of the DU alloy can make the fragment head sharper and the penetrating ability enhance. Under the same conditions, the penetration capability of cylindrical fragment impacting target in vertical posture is better than that in horizontal posture, and the penetration capability of the spherical fragment is slightly better than that of cylindrical fragment.     

An interface shear damage model of chromium coating/steel substrate under thermal erosion load

The Cr-plated coating inside a gun barrel can effectively improve the barrel's erosion resistance and thus increase the service life.However,due to the cyclic thermal load caused by high-temperature gun-powder,micro-element damage tends to occur within the Cr coating/steel substrate interface,leading to a gradual deterioration in macro-mechanical properties for the material in the related region.In order to mimic this cyclic thermal load and,thereby,study the thermal erosion behavior of the Cr coating on the barrel's inner wall,a laser emitter is utilized in the current study.With the help of in-situ tensile test and finite element simulation results,a shear stress distribution law of the Cr coating/steel substrate and a change law of the interface ultimate shear strength are identified.Studies have shown that the Cr coating/steel substrate interface's ultimate shear strength has a significant weakening effect due to increasing temperature.In this study,the interfacial ultimate shear strength decreases from 2.57 GPa(no erosion)to 1.02 GPa(laser power is 160 W).The data from this experiment is employed to establish a Cr coating/steel substrate interface shear damage model.And this model is used to predict the flaking process of Cr coating by finite element method.The simulation results show that the increase of coating crack spacing and coating thickness will increase the service life of gun barrel.     

几种UWB-SAR窄带干扰抑制方法的分析和比较

SAR(Synthetic Aperture Radar)信号处理窄带干扰抑制技术是SAR抗干扰技术的重要内容。对3种UWB-SAR(Ultra-W ideBand Synthetic Aperture Radar)窄带干扰抑制方法———陷波滤波法、AR模型参数化干扰抑制法以及小波包分析自适应干扰抑制法进行了分析,利用自行开发的成像软件,对SAR理想点目标和实录数据进行干扰抑制仿真实验,从定性和定量的角度对3种方法的干扰抑制效果作了比较。     

爆炸复合接头剪切强度测试方法研究

参照正交各向异性层压复合板层间剪切强度的测试方法,提出了用于测试爆炸复合接头复合界面剪切强度的3种方法;并建立三维有限元模型,分别对3种测试方法进行模拟;最后分别对3种方法进行了测试试验.结果表明,3种试验方法均能有效测试爆炸复合接头的剪切强度,其中对称试件双切口拉伸法最适合实际应用.